Champion HR25-12, 25HP Two-Stage 120-Gallon Horizontal Air Compressor Unit 460V

  • USA Made
  • Disc Valves
  • 460-Volt
  • Rated at 90.1cfm at 175psi, 175psi Max
  • Very Slow 770 Pump RPM
  • Motor Starter Included
  • 3-Year Limited Warranty
  • 1365 lbs
  • L– 74’’ W– 27’’ H– 64’’

Freight Paid to any 48 state destination*

$9,444.94

Description

Champion R Series 25HP 4-Cylinder 2-Stage 120-Gallon Horizontal With Motor Starter, belt Guard After-cooler, Electric Timer Auto Drain, Disc Valves, Centrifugal Unloader, Dual Control (constant run and start stop operation), Low Oil Stop Switch, Vibration Isolators

Champion R-Series Compressors have a time-tested, proven design. Rugged standard features, a wide selection of configurations, and quality available options make the R-Series compressors the solution to your application. Delivering high performance, long life and tremendous value. Champion compressors are the proven choice!

  • USA Made
  • Disc Valves
  • 460-Volt
  • Rated at 90.1cfm at 175psi, 175psi Max
  • Very Slow 770 Pump RPM
  • Motor Starter Included
  • 3-Year Limited Warranty
  • 1365 lbs
  • L– 74’’ W– 27’’ H– 64’’

Freight Paid to any 48 state destination*

 

Features

Multi-finned Cylinders Cooler temperatures result in longer life and consistent performance over time. Integral Cylinder/head Gasket-less design eliminates the possibility of blown head gaskets for trouble-free operation. Balanced Pistons Aluminum alloy first-stage piston is weight-matched to the cast iron second-stage piston, ensuring proper balance. Piston Rings: Three compression rings and one oil control ring provide excellent oil control, minimum blow-by and high efficiency air delivery. Lightweight Connecting Rods High-density, die-cast aluminum alloy rods minimize reciprocating weight. An integral precision-bored crank pin bearing and a needle bearing for the piston pin properly distribute bearing loads for longer bearing life than bushings. Pressure Relief Valves Located in interstage and discharge. Intercoolers Large-diameter finned tubing is positioned to obtain the greatest cooling effect between stages for maximum compressor efficiency. Optimized Cooling Fan/flywheel Precision balanced fly wheel has fan blades for optimum compressor cooling and life. Reliable, High-flow Valves Single-unit, disc-type valves provide low lift and long life. Discs are made of corrosion resistant Swedish steel. Valves are easily serviced by removing the manifolds only. Over-sized Main Bearings Tapered roller-type main bearings deliver the longest possible life. Balanced Crankshaft Constructed of rugged ductile iron with large diameter throws for minimum bearing loads and counterweights to minimize vibration. Large Capacity Crankcase Rugged cast iron oil reservoir has convenient sight gauge glass, corner oil fill boss and large oil drain. Load-less Starting Positive acting, governor-type centrifugal unloader assures longer motor life by allowing the compressor to start unloaded every time.

 

Options Included

Mounted magnetic starter

Vibration isolators

Electric Automatic tank drain

Low Oil Stop Switch

Air-cooled Aftercooler

Dual control

 

Available Options

  • Multiple tank sizes and variations
  • Electric or engine driven
  • NEMA 4 full-voltage starter upgrade
  • ODP HE/TEFC/TEFC HE motor upgrades
  • Control panel upgrades
  • Aftercooler
    • Air-cooled with or without moisture separator
    • Water-cooled with or without moisture separator
  • Low oil-level monitor (NEMA 1 or 4)
  • Dual control
  • Vibration isolators
  • Synthetic lubricant
  • High temperature switch (NEMA 1 or 4)
  • Available switches (NEMA 1 or 4)
    • Test/Off/Auto
    • Hand/Off/Auto
    • Off/On
  • Automatic tank drain

 

 

 

Additional information

Weight 1675 lbs
HP

25

Voltage

200, 230

Phase Configuration

3

PSI Configuration

175